SATLOOK MICRO TOOLS + SATLISTEN + neue Firmware 1.9.2010   |
so-mm
offizieller Supporter


Registration Date: 28.06.2005
Posts: 190
Schüsselgröße / Dish size: 1m Standort / Location: NRW
Level: 31 [?]
Experience: 360,913
Next Level: 369,628
 |
|
| RE: SATLOOK MICRO TOOLS + SATLISTEN + neue Firmware 10.05.2010 |
 |
hallo Leute,
es gibt ein neues Update: micro_g2-hd_firmware_115-eu.rar
This is version smG2HD-115-EU which adds UniCable testing and an RF Level Thermometer to the DiSEqC command screens.
UniCable Testing: The "UniCable Band" command is added to the Setup menu. This allows the User Band for commands to be changed from the Power On Default of User Band 0, and has a test to check if the four User Bands are there. The Test turns on the four RF tones and then for each tone tries to shift the tone 20MHz (by issuing a command with a known "No" response) and verifying that it has shifted. The spectrum display for UniCable in the Micro displays the Satellite frequency and allows the User to scroll through the spectrum 100MHz at a time. I found an issue in this area where if the knob was turned slowly move to the next 100MHz band, it worked correctly, but if the knob was turned quickly, a wrong frequency was commanded. This is now fixed. DiSEqC Commands The DiSEQc commands have been changed to add an RF Thermometer so that when a DiSEQc command is issued, the user can see the response. For the DiSEqC Positioner commands of "Go East" and "Go West", these operate as before so that as long as the button is held down, the positioner continues moving, and when the button is released, a "Halt" is issued.
__________________
schöne Grüße vom Sponsor Nr. 2
www.so-mm.de
|
|
17.08.2010 16:16 |
|
|
so-mm
offizieller Supporter


Registration Date: 28.06.2005
Posts: 190
Schüsselgröße / Dish size: 1m Standort / Location: NRW
Level: 31 [?]
Experience: 360,913
Next Level: 369,628
 |
|
| RE: SATLOOK MICRO TOOLS + SATLISTEN + neue Firmware 10.05.2010 |
 |
hallo Leute,
es gibt ein neues Update: micro_g2-hd_firmware_116-eu.rar
Here are the changes and additions for version smG2HD-116-EU:
1) In Digital mode, if the display was switched to the Large
Constellation, then the beeper would continue to sound, but SNR changes
would not change the pitch. Fixed.
2) In Spectrum mode, a beeper function is added to report the signal
level at the cursor with pitch changes.
3) The spectrum sweep always was set at 3 on power up. Now the spectrum
sweep is set to 3 when the firmware is upgraded, and from then on is
saved as the user last set it.
4) The knob acceleration has been improved so that large changes in
frequency (or positioner angle and others) can be selected easier.
5) Improve the Digital -> Search for lower levels by changing the dB
threshhold from -70 to -85. This does make the search slower, but will
now lock on low level signals. Tested with 20+ dB attenuator insertion.
6) Add the "lock boxes" similar to the G2. For the G2 demodulator, these
represent the same four phases of lock,
QPSK Lock
Descrambler Lock
Byte Align Lock
Viterbi Lock
For the HD demodulator the same indicators are not available so these are:
Tuner Mixer Lock
Tuner DAC Lock
FEC Lock
Demod Lock
7) Add Turkish to the language selections available.
8) On firmware upgrade, set the default BlindTune Modulation to 3.
(Turn off the Low Symbol Rate search)
9) Add a mode "Analog NIT" which replaces the second LNB thermometer bar
with a NIT search in the band. Switching back to the standard view is a
function in the Analog menu which is a saved parameter so the user
selection is retained at power on. This is working reasonably quickly
for satellites like 13E or 19.2E, but can be considerably slower for
some like 7E.
10) "Searching" and "Not Locked" on Digital mode was only in English.
Change these message to the language in use.
11) Add a function on Digital menu "Tuning" to manually tune hard to
lock signals. Normally, the demodulator will try a symbol rate and FEC
(and for the BCM4506 a modulation) only for a while and if no lock will
try another. This allows setting of modulation, FEC and symbol rate for
demodulator and will remain with these settings until knob turned.
__________________
schöne Grüße vom Sponsor Nr. 2
www.so-mm.de
|
|
30.08.2010 19:38 |
|
|
focki
Feediator
   

Registration Date: 27.10.2008
Posts: 256
Schüsselgröße / Dish size: 90 Standort / Location: Insel Rügen - De
Level: 28 [?]
Experience: 174,724
Next Level: 195,661
 |
|
Verändert haben sie ja nun wieder einiges aber wirklich wichtige Dinge wie das nicht funktionierende EasyFind durch den ollen Beeper haben sie nicht verbessert.
Bugliste - was mir negativ aufgefallen ist
- SR werden im Digitalmodus falsch angezeigt. Es sind immer 31 zu viel (22031 anstelle 22000 / 27531 anstelle 27500) (bei FW 115 sowie bei 116)
- Spectrum fehlerhaft. Die "springenden" Transponder (mal da, dann schwächer und mal weg bei jedem Durchlauf) Das hatten wir bei der 113 oder 114? auch schon.
- Spectrum unvollständig. Lowband wird angezeigt Highband fehlt, nur kleine Spitzen
Das wichtigste !!!
Im EasyFind Modus eine Möglichkeit schaffen den SN Beeper auszuschalten damit man EasyFind endlich wieder nutzen kann. So verliert das Gerät immer wieder sein Lock und die gesamte Funktion ist unbrauchbar.
Am besten ein EasyFind Menü hinzufügen oder im Setup Menü das abschalten des Signalbeepers und des SN Beepers ermöglichen.
Kannst du das bitte an Emitor weiterleiten damit die das endlich nachbessern.
Danke
focki
|
|
30.08.2010 20:54 |
|
|
FrAnKy
Signal-Siggi

Registration Date: 04.11.2009
Posts: 13
Standort / Location: Ostwestfalen
Level: 13 [?]
Experience: 4,030
Next Level: 4,033
 |
|
... Beschreibung wie 116!?
ev. ein Korrektur - Release
smG2HD-117-EU.rar 327.77 Kb
__________________ SATLOOK Micro G2 NIT
(kompl.Plexiglas Version)
|
|
31.08.2010 18:47 |
|
|
so-mm
offizieller Supporter


Registration Date: 28.06.2005
Posts: 190
Schüsselgröße / Dish size: 1m Standort / Location: NRW
Level: 31 [?]
Experience: 360,913
Next Level: 369,628
 |
|
| RE: SATLOOK MICRO TOOLS + SATLISTEN + neue Firmware 1.9.2010 |
 |
hallo Leute,
es gibt ein neues Update: micro_g2-hd_firmware_117-eu.rar
was genau neu ist erfahre ich heute.
__________________
schöne Grüße vom Sponsor Nr. 2
www.so-mm.de
|
|
01.09.2010 06:02 |
|
|
focki
Feediator
   

Registration Date: 27.10.2008
Posts: 256
Schüsselgröße / Dish size: 90 Standort / Location: Insel Rügen - De
Level: 28 [?]
Experience: 174,724
Next Level: 195,661
 |
|
Ich denke das ist nur die Fehlerbeseitigung von der letzten Katastrophe.
Kannst du bitte mit Nachdruck um das Abstellen des Beepers im EasyFind Modus bitten. Das macht diesen unbrauchbar!
Danke
|
|
01.09.2010 08:47 |
|
|
Prinz
Signal-Siggi
Registration Date: 07.10.2006
Posts: 11
Level: 18 [?]
Experience: 15,770
Next Level: 17,484
 |
|
Und heute wieder eine neue Version:
smG2HD-118-EU.rar
Gleiches Changelog...
|
|
01.09.2010 22:43 |
|
|
focki
Feediator
   

Registration Date: 27.10.2008
Posts: 256
Schüsselgröße / Dish size: 90 Standort / Location: Insel Rügen - De
Level: 28 [?]
Experience: 174,724
Next Level: 195,661
 |
|
Wenn ne neue FW fehlerhaft ist dann sind sie ja recht fix mit dem Nachbessern.
Ich frag mich nur warum die das nicht im Vorfeld ordentlich testen.
|
|
02.09.2010 07:59 |
|
|
focki
Feediator
   

Registration Date: 27.10.2008
Posts: 256
Schüsselgröße / Dish size: 90 Standort / Location: Insel Rügen - De
Level: 28 [?]
Experience: 174,724
Next Level: 195,661
 |
|
Haben die bei der 118 was geändert?
Ich habe wieder die 115 drauf. Da fallen mir die wenigsten Fehler auf.
Bei den neueren ist zumindest das Spectrum absolut unbrauchbar. (krumme, fette und hopsende Transponder)
Auch erschließt sich mir der Sinn nach der Veränderten Analog Anzeige (Auslsen der NIT) mit Blick auf das versaute EasyFind nicht wirklich. 2 Funktionen für einen Zweck
|
|
07.09.2010 08:44 |
|
|
|